Description
EverEdge is the permanent solution to the age-old problem of maintaining neat edges for lawns, path edging, flower and vegetable beds, and can be used in a variety of soil conditions.
The Cor-Ten option is a highly attractive and practical solution, as this unique product features a special steel-finish coating which weathers naturally and creates a rusty effect over time (approximately 1-2 months depending on rainfall).
Advisories
- Please note: The strength of the steel is not affected due to the rust sitting on top the metal, therefore protecting it against the elements.
- CorTen steel and Galvanised steel can have sharp edges and extra care must be taken when installing these products in properties with children or pets. If you would like advice on whether these finishes are suitable for your garden please call us on 01902 440250.
Our Lawn Edging Iron is available to assist with the installation of EverEdge.
EverEdge Cor-Ten Installation Examples



Dimensions
- Length - 1 metre lengths that come in a pack 5 x 1m strips
- Heights - 100mm (4") and 125mm (5") excludes spikes
- Thickness - 1.6mm
Easy to Install, No Maintenance
EverEdge is very easy to install. Once a neat edge has been created, the only tools you will need are a heavy hammer or mallet, a screwdriver and a block of wood. EverEdge is engineered from 1.6mm gauge galvanised mild steel, coated with corrosion-resistant black paint finish. So once it's installed, it's maintenance-free.
To anchor EverEdge securely in poor ground conditions, use the Pin & Sleeve System.
Installation
- It is important to form either a new edge or to re-cut your existing edge. This can be straight or curved.
- Place EverEdge where required. Take a block of wood and place on top of the EverEdge and hammer in to the ground to approximately 15mm below your cut grass level. Curve or bend EverEdge as required.
- Link EverEdge by locking on to the previous piece. There is also a tongue below the locking piece which should be pushed through the hole with a screwdriver.

For further information on EverEdge Cor-Ten, please contact a member of the sales team on
FAQs
Due to the overlapping design, you should add 6% to your actual measurement. This equates to 6 cm of extra EverEdge per metre to account for the necessary overlap when linking the sections.
EverEdge is crafted from 1.6mm gauge galvanized mild steel and coated with a corrosion-resistant paint finish. This construction ensures durability and rust resistance, making EverEdge maintenance-free once installed. It means you do not need to worry about upkeep once it's in the ground.
Installing EverEdge requires only a few basic tools. These include a heavy hammer, a screwdriver, and a block of wood, in addition to establishing a neat edge to begin with. You do not need any specialist equipment.
EverEdge comes in 1- metre lengths with 5 strips per pack. It is available in heights of 75mm (3"), 100mm (4"), and 125mm (5"). The standard thickness is 1.6mm (Classic).
First, establish or re-cut a neat edge, whether straight or curved. Place the EverEdge along the desired line, using a block of wood and a heavy hammer to drive it into the ground to about 15mm below the grass level. Bend or curve as needed and link the sections by overlapping and securing with the tongue and slot mechanism, pushing the tongue through the hole with a screwdriver. The top of the EverEdge panel should be level with the point where the soil and grass meet.
No, once properly installed, EverEdge requires no further maintenance due to its durable, corrosion-resistant, paint-coated galvanised mild steel construction.
Cutting is generally not advised, and instead you should overlap or bend any surplus length. If cutting is absolutely necessary, it's essential to paint the bare edges with a good quality primer to prevent rust.
Yes, CorTen steel and Galvanised steel EverEdge can have sharp edges. It is crucial to exercise caution, especially in properties with children or pets. Contact the manufacturer for advice on whether these finishes are suitable for your particular situation if you have any concerns.
Delivery and Returns
Delivery charge (if applicable) applied at checkout. Next working day delivery is available on some products, as an option on orders placed before 1pm - excludes festive season & bank holidays. Please note deliveries to Highlands, Cornwall and more remote areas may take longer. Surcharges apply for non mainland locations, call for more information - More delivery information.
We require deliveries to be signed for. If no one is available to sign for your delivery, you may request it is left in a safe place by leaving a signed note for the driver, requesting the item is left without a signature. Please note that this is left at your own risk and at the driver's discretion.
For large orders, please be aware that if you require a smaller 7.5 tonne lorry, the maximum weight for pallets is 750 kg - otherwise the standard pallet size limit of 1000 kg applies.
Please note for deliveries that require a pallet, the pallet/packaging itself is the customer's responsibility and will not be uplifted or taken upon delivery.
If you have any access restrictions for lorries or large vehicles please speak to our sales team on +44 (0)1902 440250.
Collection from our Telford, Shropshire, Trade Counter is available for this product - More collections information.